Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Hydraulic Piston Question


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Hugh MacKay on February 12, 2004 at 12:44:12 from (209.226.106.19):

In Reply to: Hydraulic Piston Question posted by scotty on February 12, 2004 at 11:26:22:

Scotty: Wrong board, hahaha. We'll have to put you in the same catergory as the guy asking the Case question other day. We will not tar and feather you but the other board might for not asking them first.

Now seriously are you saying there is large nut around end of cylinder where ram enters the cylinder. You might just try tightening that nut if it is as I described. Some of those cylinders rely on tightness of the big nut keeping seal tight. It will probably only be a short term solution. When the ram is fully extended are there any marks on the ram? If there is you probably will need to take the whole cylinder to a hydraulic shop. What happens here is forign objects get where they shouldn't be as you tip bucket and score the ram. Those score or scratch marks damage the seal. This doesn't happen often, but is also quite hard to avoid 100% of the time. The seals can also just fail with time. And yes cylinder does have to come apart to replace the seals. Hydraulic shops can also repair a lot of marks on rams. By the way on terminology the piston is inside on the end of the ram. If you are doing this there are also seals on piston inside, they will not leak externally. It will just allow oil to bypass the piston and the bucket be tipping towards the dump position if they are bad. Any questions you know what to do.


You indicated to me before the loader my have been not in use for awhile, thus the seals may have just dried out, that is the simple fix.


Follow Ups:




Post A Followup

:
:

: Re: Re: Hydraulic Piston Question

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Choosin, Mounting and Using a Bush Hog Type Mower - by Francis Robinson. Looking around at my new neighbors, most of whom are city raised and have recently acquired their first mini-farms of five to fifteen acres and also from reading questions ask at various discussion sites on the web it is frighteningly apparent that a great many guys (and a few gals) are learning by trial and error and mostly error how to use a very dangerous piece of farm equipment. It is also very apparent that these folks are getting a lot of very poor and often very dangerous advice fro ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy