Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

End Play Discovered


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by SGT K on January 18, 2004 at 01:00:36 from (65.120.161.56):

To Ed, ACES, rebuilder, 42FarmallH

I discovered the source of my excessive end play. On the right side, which needed the seal changed badly, I found my outer bearing was loose in my bull pinion assembly and on the shaft. Not bad, but enough for this farm boy to know it just wasn't right. For better or for worse, I peened the housing to hold the outer race and the shaft to hold the inner race, then lock-tighted them. Now the brake drum holds the inner race tight, and the outer race holds the shaft tight in the housing.

I think this is exactly what you were telling me, but I just couldn't grasp the idea until I had it in my hands. Now, the question is, will it hold? I found a used bull pinion housing I could have purchased, but I feel pretty good because the assembly went together pretty tight. If it fails I bet I can fix it in a lot less time, thanks to your advice on how to get it apart. Besides, I'm having such a good time!

Following your advice I went ahaid and took the left side out too. This went much easier because the axle slid out and I did not have to remove the entire axle housing. The left side wasn't as bad, but it needed a little attention too. Also, I lef the shims alone. If I would have removed shims after I tightened up my bull pinion housings I would never have known what affect I was having.

Now I have two brake shafts with only bearing end play, and new seals, however; if the rear end locks up on my maiden voyage down the lane, please excuse me if I don't post this fact.

I'm sorry if my post is a little long-winded, but I am very grateful for the advice I received.
SGT K


Follow Ups:




Post A Followup

:
:

: Re: End Play Discovered

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy