Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Re: Re: cub cadet paint


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by lee on January 17, 2004 at 19:10:40 from (24.24.92.235):

In Reply to: Re: Re: cub cadet paint posted by RICK on January 17, 2004 at 14:25:01:

I use a viscosity cup to measure the viscosity for thinning for my spray gun. The viscosity cup is a cheap plastic dipper like cup you can get at an automotive paint store The cup has a hole in the bottom. You dip it in the paint, pull it out and time how long it takes to empty the cup. 18 to 21 or more seconds should be in the ball park. What works best will depend on your equipment
setup and conditions. Adjust the viscosity as required and test spray to find what works best. You can just count it down or use a watch with second hand. I do it this way because it makes for very consistent viscosity every time. You don't have to measure the paint or thinner. You can thin up just the amount you think you need. Put some paint in a clean cup and add a little thinner. Stir it good and test the viscosity. Add thinner as required to get the viscosity where you want it. I would use VM&P Naptha as thinner for alkyd enamel. If you don't want to use this method I think you just have to try the recommendation on the can of paint you have. Case IH Iron/Guard is up to 8:1 (paint to thinner) reduction. Other paints may say they can be thinned 15 to 20%. I like the viscosity cup so I don't have to measure and thin by percentages or ratios. Always mix in a separate cup and then strain your paint into the clean paint cup you use with your gun. Paper strainers are available at the auto paint store.





Follow Ups:




Post A Followup

:
:

: Re: Re: Re: Re: cub cadet paint

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Niagra View Mobile - Powered by a 1959 Ford Tractor - by Mark Massey. In 1959 the Niagara Frontier Transit Inc. of Buffalo, New York designed and built six Viewmobiles for the Niagara Frontier Sightseeing Inc. for use as a sightseeing ride at the Niagara Falls State Park, Niagara Falls, New York, powered by a 1959 Ford 611 Tractor. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy