Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: 3 part ignition/starter question


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Rebuilder on November 30, 2003 at 12:04:24 from (66.228.102.204):

In Reply to: 3 part ignition/starter question posted by farmallsc on November 30, 2003 at 11:13:59:

Farmallsc: Is the sc the tractor starter you are talking about? If so I have had no problems with customers changing 6v to 12volt. The starter should work just fine as long as you keep a good charge in the battery. This helps give a quick start. If you sit there and crank for awhile you will melt the solder out of the coil/stud connection. On the smaller I.H. motors it does not take much cranking power. I don't see 12volt starters until you get up to the 300/400 series Farmalls. Bigger motor so 12/coil is more critical to handle the amps.

As far as not having a pull switch I see that as a plus unless you want to look original. THe pull swicthes I feel are a weak point as they arc every time you start the tractor and in short time the button stud has to be replaced. So a bolt on stud(threaded stud coming out of the starter) has fewer problems.

Ways you can check starter are to remove and while it it still wired up hit the switch. Make sure it turns freely. If it turns only in certain positions the amrature is shorted out. I f there is quite a bit of greasy oily residue on and around the coils rebuild the starte I have had Bad luck trying to clean the residue off and getting the starter to work. The oil works into the coil and eventually shorts out the windings. For this reason 80% of the starters I rebuild have new coils in. If when you hit the switch the brushes on the armature are sparking execsively, you should clean the copper on the amrature with emery cloth. If you still have problems make sure your electrical conections are good. I've had many an Irate customer want a warranty only to find out it was not the starter, just poor grounding or loose/corroded wires. good luck.




Follow Ups:




Post A Followup

:
:

: Re: Re: 3 part ignition/starter question

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy