Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Stuck F-20N - What Next?


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by The Red Baron on October 20, 2003 at 18:35:46 from (152.163.252.227):

In Reply to: Stuck F-20N - What Next? posted by Tony on October 20, 2003 at 09:47:36:

I had a look at those picture after sending that other reply. They look a little worse than I expected. You may in fact have to replace some of them but don't just simply remove them all without checking. I too have an F-20 I am ready to begin work on just as soon as I can get a proper place to store my F-12.

After reading your post I had to wince at the thought of anyone bashing apart a manifold with a hammer because the nuts were stuck. Those nuts were almost certainly bronze and are meant to combat rust. I'm sure you could have gotten them off if you had used the proper approach. I your penchant for using a hammer is going to cause you much grief whether or not the piece to be removed is shot or not. Next time take a PROPANE torch and heat that nut for 3-4 minutes...the expansion will work wonders. If it is unusually stubborn spray the bolt but not the nut with something like WD-40 to cool and shrink it. Next work that nut with a good half inch socket a little out and then tighten it back a little. If you don't twist it back and it is full of rust you risk torquing the stud in half and then you really have problems. Constantly working it out a little and then back in not quite as much as you loosened it. Keep spraying it with liquid wrench to wash away the loose rust that will begin accumulating ahead of the loosening nut. You surely don't want to get it jammed in the threads. I have found very few nuts that I was not able to remove this way.


Follow Ups:




Post A Followup

:
:

: Re: Re: Stuck F-20N - What Next?

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy