Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Mounting one-piece wheel weights on an M


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Bob M on July 15, 2003 at 09:09:34 from (165.170.128.65):

In Reply to: Mounting one-piece wheel weights on an M posted by Lowell Davis on July 15, 2003 at 08:24:20:

Lowell - That's a tough job to do solo! If possible I utilize the services of my 25 year old son for stuff like that. However I've installed/removed them several times on my SH and SM (wheels set dish facing out) by myself. Here's how I do it:

1 - Put on your steel-toed boots, then park your tractor on soft grass and (safety first!) Stop the tractor so one of the weight mounting holes in the wheel is at 12 o'clock.

2 - Roll the weight next to the tire and orient the weight so the two flat edges in the weight's center opening are at the top and bottom. Now lift the weight and set it temporarily on the axle.

3 - Take one of the weight mounting bolts and insert it thru the top bolt hole in the weight. Then jam a soft wood chip, piece of foam packing or similar between the bolt and the hole in the weight to temporarily hold the bolt in the hole (to keep the bolt from getting pushed out in the next step)

4 - Now comes the hard part! Hike the weight up off the axle, align the bolt with the hole in the wheel, then slide it in to the wheel as far as you can. If you do it right and don't push the bolt out, there will now be enough thread showing on the backside of the wheel to catch a nut. But don't tighten the nut yet...

5 - Rock the weight back and forth as required to align the wheel and weight holes, then insert the other 3 bolts.

6 - Finally thread the other nuts on and tighten them all down. (Don't know if this is "correct" but I use lockwashers under the bolts)

Since your wheels are set dish facing in, mounting the weights may be easier. May be able to get them into position by lifting with a loader, come along, etc. and avoid the manual lifting like I must do.

Good luck (and watch your back!)





Follow Ups:




Post A Followup

:
:

: Re: Re: Mounting one-piece wheel weights on an M

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Women and Tractors - More Views From the Farmer's Wife - by Teri Burkholder. The top ten reasons why the judges wouldn't let you participate in the stock antique tractor pull: Hey, this is stock! It came with that V8 in it! That "R" on my tires stands for "really old" not radial! Blue gas? We thought it was a pretty color! What wire hooked to my throttle? ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy