Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: H fanbelt needs to be tightened?


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by john d on July 13, 2003 at 22:23:24 from (64.12.97.13):

In Reply to: H fanbelt needs to be tightened? posted by John on July 13, 2003 at 19:20:22:

The nut will likely loosen fairly easily. Remove it and the setscrew completely. Attack the built up crud on the hub and the threads with a small wire brush and some cleaner. I replaced the belt on my M last winter, and it had been nearly 40 years since it was moved, also!

I had pretty good luck cleaning mine with a can of spray Gum-Out, a small brass-bristle brush about 1/2" wide, and some PB Blaster penetrating oil. Mine had the usual build-up of crud on the threads, and had accumulated a tremendous amount of fine dust into the threads. This dust had effectively locked the hub of the pulley in place so tightly that the setscrew and nut would not have been needed!

Use some caution when attacking the hub with a punch to turn it. Don't lose patience, or you will hit it too hard, crack it, and then be in for a much larger adventure. Turn the setscrew hole to the top, flood the inside of the hub with the solvent of your choice, then work the hub back and forth as you are able to. It may need to soak all night before you can move it. Once it starts moving, keep working it both ways until it becomes free enough to turn with your hands.

Take a good look at that belt when you start this project. If it's old, hard, cracked, or visibly worn, you may want to cut it off and make the job of loosening the hub easier. If you end up replacing the belt, you probably won't have to do all this for another 30 years or more.




Follow Ups:




Post A Followup

:
:

: Re: Re: H fanbelt needs to be tightened?

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy