Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Sorry! Our Phone System is Down. Please use our Contact Us Form.

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: 350 Utility hydraulic troubles...


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by dick on June 05, 2003 at 08:45:29 from (67.31.150.27):

In Reply to: 350 Utility hydraulic troubles... posted by Steven@nd on June 04, 2003 at 16:38:17:

Assuming "engine pulls" means it's under load and absent gross external leaks in your hydraulic system, your problem is most likely in the pressure regulating/safety valve, located next to the reservoir in the rear gang of valves. What you have now is a continually loaded hydraulic pump which is deadheaded (i.e., producing maximum pressure) when none of the control valves is active; when you activate a valve to run the lift up and down, most of the hydraulic fluid has some place to go, the hydrualic pressure is much lower, and consequently the engine isn't working nearly as hard.

Inside the regulating/safety valve is an orifice which provides a small amount of flow to the hydraulic control circuit. Hydraulic pressure downstream of the orifice allows the output of the hydraulic pump to circulate back to the reservoir at low pressure, unloading the pump - this is not happening in your system. The way it's supposed to work is that when a control valve is activated, pressure in the control line drops, the hyraulic fluid is directed to the proper cylinder rather than back to the reservoir, and the hyraulic pump supplies the pressure needed (up to the maximum 1200 psi or so limited by the safety valve) to lift the load.

When the orifice which supplies pressure to the control line gets plugged, there is never any pressure in the control circuit downstream of the orifice, and the hydraulic pump is continually loaded. As a result, a high percentage of the engine's power ends up going into the hydraulic system, and the hydraulics end up getting very hot. The life expectancy of the pump is also very short under these conditions. I'd strongly suggest you fix this promptly and not use the tractor until then. Good luck, and email me if you'd like more information.


Follow Ups:




Post A Followup

:
:

: Re: Re: 350 Utility hydraulic troubles...

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Picking Corn - by Rick Nikolich. It was the day before Christmas shutdown at work and I asked our lead engineering expert Scott Andrzejewski what he was going to do over the holidays. He said that he had some corn that he still needed to pick with an antique one-row New Idea corn picker. Scott has a nice farm about an hour north of Lansing in St. Johns, MI. He wanted to get the rest of his corn in by the next day (Christmas Eve). We had about an inch of new snow on the ground and single digit temperatures. So in the bac ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy