Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Re: Need more help


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Hugh MacKay on May 11, 2003 at 16:52:41 from (209.226.106.3):

In Reply to: Re: Need more help posted by Gwen,KY on May 11, 2003 at 13:09:32:

Gwen: Your problem is solved. Go to the first post made by CNKS, in there he describes the use of the letters in the casting codes. He is right up on these codes, whereas I am not. He states in his post the letter Z was used in 1954, thus C would have been used in 1957, making the tractor a 1957 Farmall 130. In this case the number 772 would not be a serial number as Farmall 130, serial number 772 was built in 1956. It could not have been built with 1957 castings.

There is also a very remote chance 772 is the proper serial number and your tractor is a 1958 Farmall 140, as 140 serial number 772 was built in 1958. but it would have been late in 1958 as a few thousand 130 tractors were built in first half of 1958.

Whether your tractor is a 130 or a 140 the serial number should be on left side of clutch housing, just below the fuel tank and just ahead of hydraulic unit. Clutch housing is the part the engine bolts to. The starter is on the right side. The serial tag will be just on oposite side about same height as starter. If the tag has been removed you should find 4 small holes in casting where rivits held it in place. The tag would have been about 1-1/2" high and 3-1/2" long. The 4 hole are probably about 3/16 and were in corners of tag.

The engine serial number will be right under the number 1 spark plug, which is closest to front of tractor. On the side of engine casting will be a flat machined surface about 3/8" high and about 1-1/4" long. The number would have been stamped on that surface. It will be covered in paint, oil, grease, etc. Scrape it very gently with a knife, be careful as these number were not stamped very deep and heavy work with a knife can remove them.

We are treating you very gingerly here, I have had to erase several time getting into areas suggesting your possible age. The guys never worry about this when conversing with each other. Going back do you remember when this tractor still had the grill and hood on it. Go to the photo gallery of this tractor page and under the search area, type in Farmall 130 & 140. Look at some of the pictures and compare them to the tractor as you remember it. You will find this very valuable.


Follow Ups:




Post A Followup

:
:

: Re: Re: Re: Need more help

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy