Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: M wiring


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Steve - IN on May 10, 2003 at 23:07:24 from (12.222.17.59):

In Reply to: M wiring posted by Scott Glick on May 10, 2003 at 18:44:20:

Scott,
You don't say how many terminals your regulator has. I'll guess it has 4, like my H does.

If that's the case, the single terminal by itself on one side of the regulator runs to the A or armature terminal on the generator. Looking from left to right on the side with three terminals when the single terminal side is UP -- the farthest left is the L or load terminal -- it runs to the fuse or direct to the ignition switch (can go either way, but probably safer to run thru the fuse). The center terminal should be labelled B or Batt and runs to the ammeter, the other side of the meter runs to the battery. The farthest right terminal runs to the field coils or F terminal on the generator.

Now... if my guess is wrong, and you only have two wires because the setup has a cutout instead of a regulator, the Gen side runs to the Armature terminal on the generator and the Batt side runs to the ammeter.

If you have the 4 positon light switch, you probably have a cutout (or the machine started out life that way) If you have a 3 position light switch the tractor started life with a regulator instead of a cutout. The function of the 4th position is to burn up extra generator power so the battery doesn't get over charged -- as the cutout doesn't protect against that, it only keeps the battery from draining into the generator. If you have a 4 terminal full regulator and a 4 position light switch -- not to worry, the 4th position on the switch with the big resistor is a no-connect, not needed.

Hope this gets you started and gives you some of the why's and wherefors.... BobM has posted some really good diagrams he drew somewhere... you might find them by searching the archieves here. When in doubt -- check his drawings.

Steve


Follow Ups:




Post A Followup

:
:

: Re: Re: M wiring

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy