Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: BlacksmokeBackfire


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Bob Kerr on April 10, 2003 at 09:17:40 from (152.163.189.203):

In Reply to: BlacksmokeBackfire posted by J.Chesher on April 09, 2003 at 15:14:30:

First thing I would check is, the float in the carb! I bet it is either stuck or got a crack in it and sank to the bottom of the fuel bowl. It sounds like it is running so rich that it is getting unburned fuel into the exhaust manifold at idle and when you open the throttle up, enough air gets to it to cause it to explode in the manifold. That would also cause the lack of power problem and will also cause the oil to wash off the cyl walls and wear the sleeves rings and pistons out quick! If the float is brass and has a tiny crack, they can be hard to see, so shake the float and see if you hear liquid in it. You can also clean the float and move it around and see where the gas gets it wet. the crack will be right there.some times if the crack is extremley small you may have to warm up the float in your hand to get the gas inside to expand enough to start leaking. I have fixed them with solder before, BUT don't use too much solder! It will change the float setting when you put it back in becuase it will weigh more. If it has a cork float, better just go get a new one.


Follow Ups:




Post A Followup

:
:

: Re: Re: BlacksmokeBackfire

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy