Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: 806 Wheatland


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Harold H on February 26, 2003 at 19:08:07 from (205.188.209.78):

In Reply to: 806 Wheatland posted by Brandon on February 26, 2003 at 18:14:08:

During the earlier letter series tractors there was more noticable difference in the wheel type (McCormick or International) and row crop tractors (Farmall)than the later tractors starting with the 706, 806, 1206 series. However there were still considerable differences. We called what you call a wheatland tractor a wheel tractor. In lots of areas they were called a standard tractor. At that time, all Farmalls were row crop tractors. These comments are referred to the 706, 806, & 1206 mainly. The Farmalls were available with single front, dual tricycle front, or wide front axle. The International versions of these were only available with a wide front axle which had a complete different steering setup and front bolster setup and was also a shorter wheelbase. The whole front axle was completely different. The rear wheels were different although they did now clamp and slide on the rear axles whereas prior to this series all wheel tractors had non sliding rear wheels. The rear operators platform was completely different as were the fenders. A hand clutch was optional on the Internationals but not Farmalls. The International 706, 806, 1206 had the headlights mounted in the grille whereas the Farmall versions had them located on the side of the hood at the gastank location unless they were fitted with flat top fenders in which case they were mounted in the fenders. Three point hitch was available on both the Farmalls and Internationals. If the International you have found does not have a three point it would be difficult to add the three point but it could be done. You would have to incorporate all of the lower linkage torsal bar sensing as well as all of the upper rocker arm equipment just for a start. It would be a major project.

Harold H


Follow Ups:




Post A Followup

:
:

: Re: Re: 806 Wheatland

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Engine Rebuild Kit - by Curtis Von Fange. I always liked engine rebuild kits. They have all the replacement parts for overhauling an engine without going to the store to get gaskets, special measuring tools, or miscellaneous parts. They come neatly packaged, clean and tidy. But it's important not to let that packaging lull you into a false sense of security. The appearance of matching sleeves, pistons, rings, and bearings can cause frustration and agony if not properly measured and installed in a workshop environment. Following c ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy