Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Re: Re: Re: Re: need some help with cultivators


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Larry in CO on February 04, 2003 at 15:35:22 from (32.97.110.142):

In Reply to: Re: Re: Re: Re: need some help with cultivators posted by will on February 04, 2003 at 14:38:10:

Will, There are more differences in the H and SH than just 2 horsepower. Here is a copy of a post that STEVEN@ND posted back in August 2002 relating these differences. Thanks Larry

"H: 152 cubic inches - Super H: 164 cubic inches
H: 5.9:1 compression ratio - Super H: 6.1:1 comp
Super H had improved combustion chambers on the head, rounded with tops slanting away from the spark plug - this reduced "pinging."
Also the Super H had exhaust valve rotators while the H did not. Super H camshaft held the intake valves open longer. Crankshaft was beefed up, larger diameter main and rod journals. Aluminum pistons came in the Super H along with other improvements on the pistons. Air intake from carb was increased in size, larger exhaust ports were also utilized. Carb was increased from 1 inch to 1 1/4 inches on the Super. Super H had an all new clutch that was 10 1/2 inches instead of the 10 inch on the H. New clutch facing material had copper wire to increase the life; radial grooves reduced grabbing and smoothed the release. In the transmission there were more pilot bearings and the gears were widened and induction-hardened. Speeds were also slightly changed. Rear axle and differential had better bearings with more capacity, and of course the disc brakes. The Super H's with live hydralics had a different front cover and beefed up timing gears, also the battery was relocated to under the seat. Above info comes from Guy Fay's book "Farmall Letter Series Tractors"

In short, the Super H is NOT an H with a bigger engine, it was a whole new machine."



Follow Ups:




Post A Followup

:
:

: Re: Re: Re: Re: Re: Re: need some help with cultivators

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy