Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Re: 6v generator to 12v generator


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Dave on January 24, 2003 at 07:38:27 from (138.29.36.228):

In Reply to: Re: 6v generator to 12v generator posted by Bob M on January 23, 2003 at 19:10:31:

Bob: Good point on doubling the field current, but I have a couple engineer-to-engineer questions.

First, what is the 'weak link' in the generator? I know (now) that my 6-volt gen is running double current in the field windings, but I am also running only half current in my armature (this was the reason I considered it safe and went ahead and did it). Shouldn't this help me out? I guess it would be best to run both sets of winding below their design amperage, but I was wondering how sensitive the field actually is to over-current, especially when my armature is only making one-quarter the heat than it would if run at 6 volts. Also, the exterior field windings seem more likely to shed the extra heat. I agree this is not optimal but was also wondering how different the 12-volt field windings are from the 6-volt (wire guage, number of turns, etc).

Also, do you know what the typical rated field current is for these type generators? I guess I could go out and measure the ohms of the field and divide it into 6 (or 12), but that would not tell me what my field is rated to take. I guess I should be somewhat cautious since I think my generator is oiginal and the insulation isn't the greatest. But I was just wondering how cautious I should be. For the wndings, I would take it that the field would be the 'safer' of the two to run over-current (no brushes, etc.) I was just curious if you knew how much.

Thanks for your insightful, technical remarks. I learned something!

Dave




Follow Ups:




Post A Followup

:
:

: Re: Re: Re: 6v generator to 12v generator

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy