Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Re: Re: Where do these bolts go ?


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Bill Smith on January 19, 2003 at 13:10:33 from (63.147.130.69):

In Reply to: Re: Re: Where do these bolts go ? posted by Bria on January 18, 2003 at 21:02:06:

If the bolts are just different lenghts, they probably more than likely have to go where the cover plate is thicker (allowing the whole they go through to be longer). Either that or they go into the block where the whole is deeper but I would rather think it is the first reason. The nutted stud either had something else that bolted on the stud other than the cover plate, or the stud was threaded into the block which allowed the cover plate to be slid on over the stud and the stud could then be used as a guide for installation (the nut threaded on after several of the bolts were started). Those are the two primary reasons for use of a threaded stud/nut. In future projects you might try putting the bolts in cover plate holes when removing them from threaded holes in block during a cleaning process. When I was turning wrenches sometimes I would see up to 3 or 4 different lenghts of bolts that bolted something on. Staying really strict on keeping track of them allowed a person to reassemble exactly the way it was tore down. I don't mean to sound like a hard stickler but it really is a good system to follow. Take an engine out of modern day vehicle and tear it clear down and how many nuts and bolts do you got? Hundreds. And you have to put it back together. Good reason to have good system even on small projects. Pictures are good but it seems there is always something you forgot to take a picture of and they leave out some detail such as how long the bolt is when you take the picture of something assembled.


Follow Ups:




Post A Followup

:
:

: Re: Re: Re: Re: Where do these bolts go ?

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy