Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Help! Calling all Alis Chalmer Experts!!!


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by COWBOY on September 28, 2002 at 13:18:35 from (12.149.225.90):

In Reply to: Help! Calling all Alis Chalmer Experts!!! posted by Justin NY on September 28, 2002 at 10:45:07:

Howdy,...

When I get into a bind and can't get the correct parts (Packings), you will have to improvise like I do.

I usually take a sleeve to a Hydraulic Shop and match up O Ring's that will fit into the groove and take up most of the space but isn't much larger than the OD of the sleeve when installed.

If they are too large they will get cut uneven when trying to install them in the block and most likely leak. Usually the O Rings are thinner than the groove as most packings are half moon shaped and not round.

Then I use Permatex Ultra Blue sealer on the sleeve groove, then install the O Rings, then more silicon on the top of the O Rings.

I also use a ball hone in the lower end of the block and put a thin coat on the block bore then install the sleeve and hold it in with a clamp or weight a few days.

Only silicon the lower section where the packings contact as the head gasket seals the top end.

The Ultra Blue Silicon works well. I have had to do this on over 100 sleeves to date and no leaks. Some have been in use over 10 years with no problems.

The Ultra Blue Silicon expands and contracts better than just the straight Blue Silicon, and bonds better to the parts.

I know this is not what they reconmmended when these wet sleeves were made, but they didn't have Silicon Glues and Seals back then anyway.

The only drawback in doing it this way is it must be very clean, and to remove the sleeve at a later date, you will need a Sleeve Puller and can not tap them out like some folks do.

If you need more detailed info, E-Mail me.




Follow Ups:




Post A Followup

:
:

: Re: Re: Help! Calling all Alis Chalmer Experts!!!

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Choosin, Mounting and Using a Bush Hog Type Mower - by Francis Robinson. Looking around at my new neighbors, most of whom are city raised and have recently acquired their first mini-farms of five to fifteen acres and also from reading questions ask at various discussion sites on the web it is frighteningly apparent that a great many guys (and a few gals) are learning by trial and error and mostly error how to use a very dangerous piece of farm equipment. It is also very apparent that these folks are getting a lot of very poor and often very dangerous advice fro ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy