Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Save Me From Selling My 300U (or worse)!!


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Paul Vance on July 13, 2002 at 15:54:52 from (216.167.166.14):

In Reply to: Save Me From Selling My 300U (or worse)!! posted by gerald on July 11, 2002 at 04:49:34:

I had the same prob a w\my 300u too. There can be many causes for this proplem, most of which you have addressed, as did I before I finally found a solution.
I knew my engine was fairly used by the very light amount of smoke coming from the exhaust. My plugs were fouling about every 60 to 90 mins of use,I could deal with that, it takes me about 10 mins to wire brush the plugs and I'm good for another 60-90. Eventually I was cleaning the plugs every 10min or less...no good...
replaced:
coil with accel supercoil.
plugs
wires
cap
rotor
points and cond.
I also thoroughly went through the carb.
after going through all this and playing with dwell settings, timing, and float level, there was no difference at all. Runs very strong for 5 to 10 minutes. I did not do a compression check cause I didn't know what the spec ahould be on a 6.5 to 1 ratio engine, but I figured it probably was low. No time for rebuilding any time soon, so as a last resort I drained the oil and put in a mixture of sae 30 and 80-90 gearlube(1 to 4 ratio...3 of the 30 to 1 8090). Thicker oil will help close worn tolerences. And to boot I found some plugs that had a huge center electrode, about 1\4 in long,(less heat disipation=hotter plug)...WELL....long story longer...tractor starts instantly and have not had to clean the plugs at all and I've been running the tractor for a couple of hours a weekend for two to three months...I'm very happy. Do not do the oil thing if you know that the engine is fairly fresh(thick oil will not flow through close tolerences). The plug thing will not hurt anything. Found them at wal-mart, matched up threads and width, new ones were slightly longer but did not have any problem. The important thing is the long electrode.
Try this, if it doesn't work, I'll buy your tractor... good luck. PV new mexico


Follow Ups:




Post A Followup

:
:

: Re: Re: Save Me From Selling My 300U (or worse)!!

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Choosin, Mounting and Using a Bush Hog Type Mower - by Francis Robinson. Looking around at my new neighbors, most of whom are city raised and have recently acquired their first mini-farms of five to fifteen acres and also from reading questions ask at various discussion sites on the web it is frighteningly apparent that a great many guys (and a few gals) are learning by trial and error and mostly error how to use a very dangerous piece of farm equipment. It is also very apparent that these folks are getting a lot of very poor and often very dangerous advice fro ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy