Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: How easy to roll over on a narrow front M?


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Gene on June 17, 2002 at 13:18:36 from (64.156.66.149):

In Reply to: How easy to roll over on a narrow front M? posted by Michael on June 17, 2002 at 12:56:36:

Michael: I tipped an Farmall M over. I'll tell you how. (This was about 40 years ago) I had a very heavy stone in the bucket of the loader. I had to drive between a wagon and a fence befor turning to dump the stone. I had the bottom of the bucket about level with the bottom of the radiator. That's not real high but the load was heavy. For speed: I had it in 1st gear at about 1/3 throttle. I squeezed between the wagon and fence and started the turn when one rear wheel went into a depressed spot and wouldn't ya know it the other rear wheel just then started up a gopher mound. It was "right-on-over" in about 2 seconds. Nothing to it. The fluid filled rears didn't prevent this at all. I was not being abusive\careless as I was in LOW gear at slow RPM's. IT was 80% due to the change in surface for both rear wheels. A hole for one and a gopher mound for the other did most of the "flipping." There was only slight damage as it stoped on its side. The really bad part was that only the neighbor and his John Deere were close by to pull it back on it's feet. Heck of a good lesson and I've not forgot it can be done at very slow speed with bucket not too high. Sooner or later everyone is subject to a mishap. I did NOT stop using Narrow front ends nor was I afraid to raise the bucket if I had to... ButI was more aware of what surface the rears were on after that. Gene


Follow Ups:




Post A Followup

:
:

: Re: Re: How easy to roll over on a narrow front M?

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy