Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Re: Re: Yahoo! The big red monster lives


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by ScottyNY -- Lnng -- Don't let on April 20, 2002 at 20:59:32 from (24.169.149.69):

In Reply to: Re: Re: Yahoo! The big red monster lives posted by redrev on April 20, 2002 at 17:08:06:

the Rev fool ya any. Y'know how when a job hits a rough spot, things not going just the way the manual says it would, and you're just about to run out of native intelligence for ways around the diffugilty? Well that's where George would drop just a pearl of wisdom, or even just a good idea. I may have been turnin' the wrenches, but the Rev himself was able to mechanic some, too, so it was a joint effort all the way.

As for what it turned out to be, I think we may have had two problems going at once. I noticed right off that the fingers on the clutch were at all different distances from the face of the throwout bearing. The other was that, after pulling out the universal and unhooking the odds and ends, the shaft, clutch, and disc failed to come out "as a unit" the way all the books say they ought to. A lot of massaging before the disc would even move, so it may have been rusted to the flywheel, as well. Never did get them down. (Any thoughts on why that may have been would be welcome) The disc looked good, though, and was free so we bolted things back up. Possible that the clutch cover wasn't bolted down properly in the first place, as the fingers were better but still not right. (Amazing, ain't it, how little adjustment those things take!) The jam nut was loose on one of the bolts, and the bolt itself was spinning, less than fingertight. Since we couldn't get the whole assembly to drop, we adjusted the fingers to the face of the throwout bearing. Put her all bcak together, one more adjustment on the free throw, and she's wheeling just fine.

And apart from wrenching, I can't say enough about Mr. & Mrs. Rev and their hospitality, though, despite his generous offer to share, rev IS a tad protective of his whipped cream! To letchya know the sort of fellow he is, though, he has been kind enough (Talers take note) NOT to mention that all the while we were in the shed wrenchin, my truck was sittin' outside running the battery flat ( a little ovrsight on my part). Needed a jump before I could get started home. A long day, but no more than I'd set aside, and for those of us that love these machines and working on them,you'll know what I mean by saying that it certainly was satisfying to solve a problem, and especially for a guy that's right at the head of the list of nice folks.

Too long again! Nytol. Scotty


Follow Ups:




Post A Followup

:
:

: Re: Re: Re: Re: Yahoo! The big red monster lives

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Choosin, Mounting and Using a Bush Hog Type Mower - by Francis Robinson. Looking around at my new neighbors, most of whom are city raised and have recently acquired their first mini-farms of five to fifteen acres and also from reading questions ask at various discussion sites on the web it is frighteningly apparent that a great many guys (and a few gals) are learning by trial and error and mostly error how to use a very dangerous piece of farm equipment. It is also very apparent that these folks are getting a lot of very poor and often very dangerous advice fro ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy