Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: IHC 240 utility hyd.


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by K.B. on April 14, 2002 at 13:25:19 from (209.163.14.22):

In Reply to: IHC 240 utility hyd. posted by John on April 13, 2002 at 20:55:40:

What do you have for hydraulics right now, and how many remotes do you want to have? You can have up to three valves, with one outlet in back, and one on each side, at least thats how my 240 is set up.

Now, look under your gas tank. you should see the hydraulic valve support. It's a big piece, with the lines from the pump running in to it, and it also contains the filter. At the top of it, the regulator/saftey valve and however many control valves you have will be mounted to it. You will need to have a control valve for left side hydraulics, a control valve for rear hyd. and a control valve for right side hyd.

If you have all the parts including levers and linkages and o-rings on hand, it is simply a matter of removing the end plates and four long bolts that run through the control valves, valve support, and regulator/ saftey valve, adding your additional valves and using longer bolts to run through them. Mount valves in this order- End plate-Left control valve-Rear control valve-Valve support-Reg./saftey valve-Right control valve-End Plate. If you already have all of these parts in place all you have to do is remove plugs from the valves and add plumbing/couplers.

If you don't have all the parts, it will be hard to find them.

If you need more help, post back, or see if a local Case-IH dealer will print you off the exploded view of the hyd. valves from the parts book.


Follow Ups:




Post A Followup

:
:

: Re: Re: IHC 240 utility hyd.

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy