Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: always wondered


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by walt f on February 21, 2002 at 22:41:32 from (24.159.79.106):

In Reply to: always wondered posted by adam on February 21, 2002 at 21:56:27:

depends on how bad they're stuck. sometimes you can tell by just looking at the spark plugs when you remove them. if the plugs have little balls of rust on them, then that is usually an indicator that it's stuck pretty bad. even then, i've been surprised at how little damage is in the cylinders. you can loosen the rings when you remove the pistons from the cylinders. the key is patience. do not get in a hurry. make up a system to record the way you took the engine apart, so you can reassemble it later. before you take anything apart, find a way to flush out your cylinders thru the spark plug holes. i purchased a squeeze bulb like you use to add water to a battery, and put a 12 in. rubber fuel line on it. i put a half cup of gas and a tablespoon of fuel system water remover in each cylinder. i then used the squeeze bulb to suction the fuel mix into the bulb and squeeze it out again flushing the cylinder, mixing the liquid with the rust and moisture in the cylinder. i did this about ten times in each cylinder and walked away for a few minuites to do something else and came back and repeated the process over again. i did this about four times to completely saturate the the cylinder and down the sides of the cylinder, then i removed as much of the liquid as i could with the squeeze bulb. on my tractor (f-20) my sparkplug holes are big so i could stuff long thin pieces of cotton t shirt down each hole to absorb the liquid left over. i was careful not to leave any pices in the cylinder!! after a day or two i was satisfied that most of the liquid was gone i sprayed some p b blaster down each hole, and let that set for awhile. i got mine loose with the hand crank..if you need more help, just ask. someone will have some ideas.


Follow Ups:




Post A Followup

:
:

: Re: Re: always wondered

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Choosin, Mounting and Using a Bush Hog Type Mower - by Francis Robinson. Looking around at my new neighbors, most of whom are city raised and have recently acquired their first mini-farms of five to fifteen acres and also from reading questions ask at various discussion sites on the web it is frighteningly apparent that a great many guys (and a few gals) are learning by trial and error and mostly error how to use a very dangerous piece of farm equipment. It is also very apparent that these folks are getting a lot of very poor and often very dangerous advice fro ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy