Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: power


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by john d on February 10, 2002 at 19:52:55 from (152.163.204.206):

In Reply to: power posted by chris on February 10, 2002 at 17:01:24:

If you're into tractor pulling, better pick the brains of the guys on that board, and have a fat wallet.

If you're farming with an absolutely stock M and a 450, you can likely get more out of each. Make sure they're tuned up properly, and that you're getting all the power the engine CAN make before doing anything drastic.

An engine re-build that features a larger-diameter sleeve/piston set for the M will increase the displacement from 248 to 264 cid. This will gain quite a bit of power. Overhaul kits are available for both models that feature higher-compression pistons. This will gain more power. Your friendly CaseIH dealer can set you up with the "fire-crater" rebuild kits that will likely include not only the sleeve/piston set, but an improvement for the distributor as well. The M is capable of 50+ horsepower if set up right. The 450 is capable of producing even more.

Another place to look for power is the governor. If you have the stock governor assembly, it's efficiency starts to drop as wear accumulates. A governor re-build will allow your tractor to use all the power it can make. If - and only IF your tractor is in sound mechanical shape, you might consider turning up the top governed speed of the engine. Opening up this setting to allow an old M to turn in the neighborhood of 2000 rpm is not unheard of, and they don't seem to suffer from it! I've got one that's been running that fast since the early 60's! It'll use more gas, but you'll plow more by the end of the day!


Follow Ups:




Post A Followup

:
:

: Re: Re: power

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy