Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: At what RPM is peak efficiency (torque) for M?


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by agpilot on May 27, 2007 at 10:58:34 from (206.146.78.170):

In Reply to: Re: At what RPM is peak efficiency (torque) for M? posted by CNKS on May 27, 2007 at 08:33:45:

Hello CNKS: With all due respect, I don't remember reading anything where IHC stated that the M engine was designed for full throttle. As a backup to this I'll point out that rated PTO RPM of 540 is obtained well below max engine RPM. Why did they not use full engine RPM power to the PTO? I can't recall all the books or manuals I've read years ago but I'll stay with my impression that the M and most other 4 cylinder Farmalls were designed with a fairly Flat torque curve from half to full RPM. Most non-turbo engines have a peak in torque about 70 percent max RPM. An earlier 425hp Corvette I had peaked torque at 5100 but Redline was 6400. I've read many of your posts and you have a very good knowledge of Farmall but I'll hold to staying with saying the M has a very usefull and relative flat output power from above half RPM to almost full RPM. Another place I can see flat output in most 4 cylinder classic Farmalls is in a tractor pull. They hang tuff untill engine RPM goes below about half. Then they fade faster.
Most aircraft piston engines have published torque curves and fuel used vs power output etc for all comercial pilots to use. Pilots have to know this to plan a safe flight. If only we had this type of info on Farmalls like I've seen for low RPM non-turbo piston aircraft engines... Hopeing your having a great weekend... agpilot


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy