Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: half turn steering slop IN farmall A


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Dave Sherburne NY on March 06, 2007 at 07:15:30 from (74.32.148.82):

In Reply to: half turn steering slop IN farmall A posted by Chad from Michigan on March 06, 2007 at 04:14:00:

This problem has been discussed several times on this Forum. There are several places which could be
worn and causing your problem. You have already
addressed one But on a tractor with that much slop
you will have to get into the steering box where
you will find a vertical shaft with a worn keyway.
and a sector gear in which the keyway probrobly
isn't worn bad.Also in there are bushings and seals
you have to replace. Plan on doing it all. The vertical shaft will have a square end on the bottom
where the outside steering arm is clamped on. To
bad, its worn out. Now if you plan on keeping the
tractor forever, You replace the vertical shaft
with one from a newer model, which has a tapered
end on the bottom. $90 on Ebay. The sector gear
will fit the shaft, but the steering arm won't
so you will have to go to your IH dealer and get a
new steering arm, not cheap. AND you have to get
the one that fits you tierod ends.
Replace these pieces and the shim Scotty mentions and all the seals and shims in there and
it will be better than new.
CHEAPSKATE SOLUTION
You still have to take off the steering
box. Replace the seals and sleeves,put in the
shim washer, Fix the keyway, but you still have
the problem of the steering arm clamp on the
square shaft. Shim it with some real thin sheet
metal and clamp it on tight.


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Choosin, Mounting and Using a Bush Hog Type Mower - by Francis Robinson. Looking around at my new neighbors, most of whom are city raised and have recently acquired their first mini-farms of five to fifteen acres and also from reading questions ask at various discussion sites on the web it is frighteningly apparent that a great many guys (and a few gals) are learning by trial and error and mostly error how to use a very dangerous piece of farm equipment. It is also very apparent that these folks are getting a lot of very poor and often very dangerous advice fro ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy