Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Re: Re: Re: Re: Priming Super C Hydraulic Pump


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Clyde on November 02, 2001 at 04:11:03 from (63.146.82.73):

In Reply to: Re: Re: Re: Re: Priming Super C Hydraulic Pump posted by gt on November 01, 2001 at 19:12:33:

The TC wasn't too bad. You're really just taking it all part, cleaning out all the passages, ports, etc. and putting in lots of new seals. You get the kit from Case IH for $89.

I had trouble getting some of the actuators out of the block. They were recessed into the block and being held by suction. My TC had been shut down with the pistons drawn in. I would try it with the pistons outward. I suspect the actuators might end up sticking out of the block slightly. Other than that make sure the outside of the TC is absolutely clean before you take it apart on your bench. I used lots of paper towels on my bench to lay the internal arts out on. I cleaned the inside of my bare block with a high pressure sprayer using mineral spirits. Dip or coat parts with oil as you put them back in. Rotate all parts with o-rings as you put them in, don't just push them in. Make sure all parts go back in the same exact place in the block since you'll have pairs of most parts. The head has to be torqued down to 45 lbs.

Took me a full day. If I ever have to do it again I could probably do it in half a day.

Oh, also be careful you don't get a hernia. That thing is heavier than it looks.


Follow Ups:




Post A Followup

:
:

: Re: Re: Re: Re: Re: Re: Priming Super C Hydraulic Pump

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Women and Tractors - More Views From the Farmer's Wife - by Teri Burkholder. The top ten reasons why the judges wouldn't let you participate in the stock antique tractor pull: Hey, this is stock! It came with that V8 in it! That "R" on my tires stands for "really old" not radial! Blue gas? We thought it was a pretty color! What wire hooked to my throttle? ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy