Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Super H disc brakes


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by john d on June 12, 2001 at 21:28:23 from (152.163.204.189):

In Reply to: Super H disc brakes posted by Bill Jones on June 12, 2001 at 18:43:03:

Pretty simple job. Pay attention to how things come apart, and do one side at a time.

Make sure you loosen the adjustment hardware before you take everything else loose. Trying to re-install the adjustment linkage with a rusted-stuck nut isn't gonna work, and you can't have much success getting it loose in mid-air.

While everything is apart, CLEAN it; REALLY clean it! Get any rust that's on the balls or the tracks they ride in out of there. Look for broken parts or pieces that are obviously worn.
Also make sure the seals on the shaft aren't leaking any transmission grease. The disks themselves will wear out long before the rest of it. If you can locate some new rubber boots for the actuating rods, get them! They help keep water out, and moisture is enemy #1 for these brakes.

Follow the instructions in the manual for adjusment, and give them a little time to break in before abusing them. A coat of paint over the housings when you're finished will help keep moisture from seeping in where the castings butt against each other.

One more thing.....you'll likely get a variety of opinions as to lubricating the balls and internal linkage. Grease will work....but if things get really hot (and brakes can get very hot!) the grease will migrate to where you don't want it! Powdered graphite will work well, but it's messy, and you don't want to put a lot of it in there. Silicone spray will work, but you'd better not spray it on the disks! It also won't last as long as the graphite. Anti-sieze thread compound will work in moderation.

These are good brakes if well maintained. They're commonly thought to be a lot less trouble free than the older band-types, but if they're working correctly, they'll freeze a rear wheel almost instantly.




Follow Ups:




Post A Followup

:
:

: Re: Re: Super H disc brakes

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Picking Corn - by Rick Nikolich. It was the day before Christmas shutdown at work and I asked our lead engineering expert Scott Andrzejewski what he was going to do over the holidays. He said that he had some corn that he still needed to pick with an antique one-row New Idea corn picker. Scott has a nice farm about an hour north of Lansing in St. Johns, MI. He wanted to get the rest of his corn in by the next day (Christmas Eve). We had about an inch of new snow on the ground and single digit temperatures. So in the bac ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy