Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

HELP!...I've got a wiring mess I'm charged up about! (ha, ha)


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Thor on May 05, 2001 at 11:09:04 from (209.130.172.129):

Hey guys,

Spring is here and my tractor doesn't run...PROBLEM! I've been doing a major reassembly, and am up to the point of getting the wiring in order. By the way, I have a Farmall 300 Row Crop. The tractor was already converted to 12 volt when I got it, but it appears to be a pretty rough job.

The ignition switch was bad and had a push button switch wired to it. You needed to turn the key to on and then push the button to start the tractor. My problems start with me getting a different switch that I know works...

Here are my most immediate questions. The tractor has a 3 wire delco alternator but only the battery terminal was used and there was/is a rubber plug over the two spade terminals, can anyone explain why this is this way? The old voltage regulator is still on the tractor. The orange and blue leads that I assume went to the generator were taped up, where should these go? Can I get rid of the old voltage regulator? What do I do with the wires that go to the voltage regulator? There is no ballast resistor that I can see anywhere, and the coil is definitely not original, I assume this is a 12 volt coil, negating the need for the ballast resistor. How can I tell if it is indeed a 12 volt coil?

Any help, advice, suggestions, support, wiring diagrams, counseling....(you get the idea!) would be much appreciated.

Thanks in advance,

Thor


Follow Ups:




Post A Followup

:
:

: Re: HELP!...I've got a wiring mess I'm charged up about! (ha, ha)

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Niagra View Mobile - Powered by a 1959 Ford Tractor - by Mark Massey. In 1959 the Niagara Frontier Transit Inc. of Buffalo, New York designed and built six Viewmobiles for the Niagara Frontier Sightseeing Inc. for use as a sightseeing ride at the Niagara Falls State Park, Niagara Falls, New York, powered by a 1959 Ford 611 Tractor. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy