Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: farmall cub magneto


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by p on May 02, 2001 at 08:26:36 from (131.210.22.106):

In Reply to: farmall cub magneto posted by Todd Hatfield on May 02, 2001 at 07:12:09:

You have discovered the impulse of the magneto. Yes! that is supposed to happen. The magneto is different from a distributor in that the magneto generates its own electricity to run. The distributor only "distributes" the electricity from another source.
The Magneto does not turn fast enough when the engine is spun for starting, so the impulse fixes that. The little arms stop the rotation of the magneto for a moment allow the springs to wind up. When the magneto turns enough to fully wind the spring, the impulse trips, which allows the magneto to turn very fast and thus create enough of an electrical current to produce a spark. If you take off the distributor cap and turn over the engine you will see this process. DON't touch anything! That shock is strong!

Brng the cub back to Top Dead Center (TDC) on #1 cylinder. Reinstall the magneto so the rotor is pointing at the number #1 cylinder. Retard the magneto timing by turning it counter-clockwise (push the top towards the cylinder head). Rotate the engine to TDC at number 1 again. slowly turn the magneto clockwise(pull towards you) until it clicks. THe timing is now set.

When the engine is running the magneto is turning fast enough and the impulse is not actuated.

hope this helps. a good manual will also help. Let me know if this helps and please feel free to ask for more.....p


Follow Ups:




Post A Followup

:
:

: Re: Re: farmall cub magneto

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy