Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Re: 240 has the hic-ups


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Rick in CA on April 11, 2001 at 15:30:02 from (207.18.199.196):

In Reply to: Re: 240 has the hic-ups posted by bob w. on April 11, 2001 at 11:21:11:

Bob,

Funny you should ask this question. I have a 240 with the same problem and I plan on working on it this weekend. I asked a similar question a couple of weeks ago and received a response. The print-out I have of the reply doesn't have the name of the respondant on it so I can't give credit where it is due. His relpy to my inquiry is as follows.
"From your description I suspect that you have an obstruction in the line going to your cylinder. If the enginer gets loaded up when you raise or lower the lift without anything on it, chances are that the pump is putting out high pressure which isn't making it to the cylinder because of an obstruction, and the system's high pressure relief valve is (correctly) relieving this pressure before it gets dangerously high - but putting out this high pressure makes the engine work hard. If you don't notice any difference between how the system acts in the middle of the cylinder's travel and at the ends of it's travel, an obstruction is almost certantly the problem.
Another tip off is if the rate at which the cylinder moves is very slow. The obstruction could be in the control valve somewhere.
If you have more than one circuit in your hydraulics, a check of how one performs verses the other would be informative."
I do have dual system on my 240 and the other side works fine. I did rebuild my control valve and it didn't buy me anything. Next is to flush the line to the rear and rebuild the check valve under the seat (I think that's what it is)
Keep me updated on your progress. It may help both of us.
Does anyone know how hard it is to rebuild the cylinder?

regards,


Follow Ups:




Post A Followup

:
:

: Re: Re: Re: 240 has the hic-ups

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Talk of the Town: Repairin a Gas Tank - by Staff. This interesting discussion is from the Tool Talk Discussion Forum. Remember that safety is your first priority - make sure you know what you are doing before attempting a potentially dangerous activity! ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy