TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Tractor Talk Discussion Forum

ford 801 3 point lift

Welcome Guest, Log in or Register

Author

ken tinlin

12-18-2007 05:12:49

Report to Moderator

i have a ford 801.the 3 point has stopped lifting to proper height.oil level is ok and lift does not surge or pulse.my book tells me we need special tools to re adjust.is there a simple way without special tools.any help appreciated thanks

[Log in to Reply] [No Email]

Keith-OR

12-18-2007 13:07:07

Report to Moderator

Re: ford 801 3 point lift in reply to ken tinlin, 12-18-2007 05:12:49

Ken, adjustments "can" be made without the special tools. If you read your service manual closely, it will give instructions on how to secure the lift arms in position(without special tool) so they don't move while making adjustments. Also the measurements of gage thickness(gage required)that you need to make the adjustments.

If you need the thickness of the gage, email me.

Keith & Shawn(Special Olympic Champion)

[Log in to Reply] [No Email]

Texasmark

12-18-2007 06:24:58

Report to Moderator

Re: ford 801 3 point lift in reply to ken tinlin, 12-18-2007 05:12:49

The special tools they refer to is primarily a forked clamp hootus that positions the lift arms with respect to the cover so that you can get the correct dimensions THE FIRST TIME on the draft spring tensioner. I have setup several by swag and have ended up close enough to be satisfied with it.

Before you jump to conclusions (that you have a problem), what is the position of the DRAFT-LIFT lever on the right side of the tractor under the seat? I think it is supposed to be down for lift and horiz for draft....but it"s been a long time and I forgot. If in draft, the lift has limited range as you move the lift lever through it"s range. I think the words are protrusions on the casting so you can see which is which by looking at it. If not, just put it one way and watch your lift arms and then move it the other and do it again. You will know when you are in the lift position.

Unless you broke something, I don"t recall that they just all of a sudden decide to not go all the way up or down, especially if it functions normally in other parts of the lift range.

HTH

Mark

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy