TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Tractor Talk Discussion Forum

Hey Allan!

Welcome Guest, Log in or Register

Author

Bill(Wis)

12-13-2007 21:19:00

Report to Moderator

There's a Gleaner Model E in the photo ads. Looks good. 800 bucks.

[Log in to Reply] [No Email]

Allan In NE

12-14-2007 01:40:32

Report to Moderator

Re: Hey Allan! in reply to Bill(Wis), 12-13-2007 21:19:00

Well, there ya go.

You better snatch that little guy up. Must run okay too; still has chaff under the floor board.

Heck, a guy could almost haul that feller on a U-haul trailer. :>)

Allan

[Log in to Reply] [No Email]

Allan In NE

12-14-2007 03:12:46

Report to Moderator

Re: Hey Allan! in reply to Vern-MI, 12-14-2007 02:19:48

Yeah But,

Those machines just don't seem to have the "experience" (read: wore out) that I need.

What I mean is, when ya find one that needs the silly ladder rebuilt, ya know it's been across an acre or two. :>)

By the way, anyone have a good, servicable feeder beater fer a F/F2? Got two of the old rascals layin' here and don't think I can even scrounge a decent one between the two. :>)

Allan

[Log in to Reply] [No Email]

JMS/.MN

12-14-2007 08:13:42

Report to Moderator

Re: Hey Allan! in reply to Allan In NE, 12-14-2007 03:12:46

I have one or two, but I imagine salvage yards closer to you should have them too. What"s wrong with yours? Mine had dents in, courtesy of rocks. Ground the weld off the end cap to remove it, went in with a hyd jack and pressed everything straight, welded the cap back on. Good time to go with the cast finger guides like the C/S machines have. Spendy part was replacing the poly sleeves that the finger assemblies turn on. I think they were about $140 10-15 years ago.

[Log in to Reply] [No Email]

Vern-MI

12-14-2007 05:47:45

Report to Moderator

Re: Hey Allan! in reply to Allan In NE, 12-14-2007 03:12:46

It would seem that they all have the same worn out parts. Can't even rebuild with a new gudgeon and hub? That Kit- Combine has to be warming up you cheek with all the friction of slipping that old wallet in and out. You don't know yet how good the hydraulics and belt drive stuff is until it fires and starts to pull itself.

[Log in to Reply] [No Email]

Allan In NE

12-14-2007 07:49:14

Report to Moderator

Re: Hey Allan! in reply to Vern-MI, 12-14-2007 05:47:45

So far it has been relatively painless and is coming in quite a bit cheaper than I thought.

There is always the unknown factor looming about, however. :>(

Got an awfully lot of stuff (including a 2nd complete hydraulic system) along with that motor and am certainly thankful for that.

The two new walker cranks kind of made my ears ring just a little tho. They don't give those things away. :>(

Now, if I can just squeeze by that darned hydro..... ....Sure as heck can't quit now. :>)

Allan

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy