Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Tractor Talk Discussion Forum

Bleeding 784 International tractor brakes

Welcome Guest, Log in or Register
Author 
Lloydie

05-22-2007 01:16:04




Report to Moderator

Could anyone please suggest ways, or links, to assist me in bleeding the brakes of a 784 International tractor?
Appreciated,
Lloydie




[Log in to Reply]   [No Email]
Lloydie

05-25-2007 18:27:20




Report to Moderator
 Re: Bleeding 784 International tractor brakes in reply to Lloydie, 05-22-2007 01:16:04  
Hi Guys,
Greatly appreciated for the responses. Have printed out your suggestions and will give it a go. Will let you know.
Thanks again - big help!
Lloydie



[Log in to Reply]  [No Email]
richard in nz

05-23-2007 04:02:58




Report to Moderator
 Re: Bleeding 784 International tractor brakes in reply to Lloydie, 05-22-2007 01:16:04  
Trans oil at working temp, at correct level.
Tractor engine running at 1,000 rpm.
Block off return tube to transmission at T piece near the bulkhead (firewall) with a pair of vice grips with protected jaws. (You will see the brake top up supply, clamp off the "overflow" that goes back to the trans so the brake master cylinders get all the available oil)
Attach pipe from the bleed screws and put the other ends of the pipes in to the trans filler cap, clear pipe is best.
Latch the brake pedals together and slowly pump the brakes.
When the first pipe becomes clear of air, tighten the bleed screw and continue pumping untill the other side bleeds clear.(keeping the brake pedals latched gets all the air from the balance valve)
Thats how it was taught at the training school at IHC in Doncaster where your tractor was built and you will find is the most reliable method even though long winded.

[Log in to Reply]  [No Email]
georgeky

05-22-2007 07:27:33




Report to Moderator
 Re: Bleeding 784 International tractor brakes in reply to Lloydie, 05-22-2007 01:16:04  
There is no need to pump the brakes. They are hydrostatic, just hold the brake pedals down with something and let the tractor run it will bleed itself. I do use the clear hoses like mentioned and return them in the filler hole, that way I can see when all the air is out.



[Log in to Reply]  [No Email]
ben brown

05-22-2007 03:10:38




Report to Moderator
 Re: Bleeding 784 International tractor brakes in reply to Lloydie, 05-22-2007 01:16:04  
i ues clear plastic line that well fit tight on bleed port top of axle housing then run over seat bacd down in to hy fill. that way you can pump the brakes tell you see fluid with out air bubbles. then cloes blead port.



[Log in to Reply]  [No Email]
Jrry

05-22-2007 06:50:59




Report to Moderator
 Re: Bleeding 784 International tractor brakes in reply to ben brown, 05-22-2007 03:10:38  
If he doesn't have a clear line he can take a regular hose and put the end in a small bucket of hy fluid and pump the brakes. He will be able to see the bubbles blowing through the fluid and when the bubbles quit the air is out and the bleeding is finished.



[Log in to Reply]  [No Email]
Ken Macfarlane

05-22-2007 05:26:23




Report to Moderator
 Re: Bleeding 784 International tractor brakes in reply to ben brown, 05-22-2007 03:10:38  
Its been a while but on the one with a cab I did you had to lift the floor panel and you could slip a wrench in while holding the pedal down. Its been 5 years or so though.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy