Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Tractor Talk Discussion Forum

FORD 4110 SOS WONT ROLL

Welcome Guest, Log in or Register
Author 
jcr

03-13-2007 22:54:36




Report to Moderator

NEED TO KNOW HOW TO GET TRACTOR TO FREE UP AND ROLL SO I CAN GET IT ON TRAILER BY ROLLING IT ON .IS THERE A WAY TO GET IT FREE UP LIKE IN NUETRAL .THE 3 CYLINDER DIESEL WONT RUN AND IT JUST SKIDS WHEN I PULL IT.ITS A YELLOW 1970'S IDUSTRIAL,TRACTOR.ACT LIKE IT IN PARK HAS A MULTI SPEED AUTOMATIC TRANSMISSION. THANKS FOR ANY INFO.NEED TO MOVE IT.IS THERE A WAY TOGET IT TO ROLL.




[Log in to Reply]   [No Email]
JCR

03-14-2007 14:44:51




Report to Moderator
 Re: FORD 4110 SOS WONT ROLL in reply to jcr, 03-13-2007 22:54:36  
THANK YOU ALL I FREED IT UP THIS MORNING. THE LEVER WAS STUCK SO I OPENED THE INSPECTION PLATE AND AFTER SEVERAL ATTEMPTS TO FREE COLLAR A BIG OPENED END WRENCH WORKS BEST BECAUSE THE OPEN END HOOKS ON COLLAR AND PRYED IT SLIPPED IT OUT.INCH AND A HALF WRENCH I THINK MAYBE INCH AND QUARTER THANK YOU.



[Log in to Reply]  [No Email]
Kevin (FL)

03-14-2007 07:16:13




Report to Moderator
 Re: FORD 4110 SOS WONT ROLL in reply to jcr, 03-13-2007 22:54:36  
Left side on trans/differential housing--look for an offset stamped steel bracket--about 2 inches long. Remove bolt and turn bracket about 90 degrees or so. This disengages a splined collar between the differential input shaft and the trans output shaft. If it"s stuck, you can bump the tractor while trying to move the lever. If it still won"t come loose, remove the cover plate and you can use a large screwdriver to move the collar. Shift SOS lever into neutral also--(this may not be necessary but I do.)

[Log in to Reply]  [No Email]
ErnieDD

03-14-2007 04:41:56




Report to Moderator
 Re: FORD 4110 SOS WONT ROLL in reply to jcr, 03-13-2007 22:54:36  
I believe it is the same as the older sos, check the left side under the seat. There should be lever bolted down, loosen the bolt and move the lever, this will disconnect the drive line. Block the wheels, it will roll now.



[Log in to Reply]  [No Email]
Turke Bros. Farms

03-14-2007 05:08:01




Report to Moderator
 Re: FORD 4110 SOS WONT ROLL in reply to ErnieDD, 03-14-2007 04:41:56  
yep search for the trans engange and disengage lever.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy