TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Tractor Talk Discussion Forum

IH 666 oil leak

Welcome Guest, Log in or Register

Author

AndyinMo

08-11-2004 05:39:52

Report to Moderator

I have a IH 666 with a oil leak behind the lift levers for the 3 point. Their is a little shaft with a snap ring on it that leaks. I pulled the seat,plate and the cylinder assembly out. I am having a bear of a time pulling that shaft with a bunch of linkages and fingers on it. I need to pull it to replace O-ring. Any help would greatly appreciated.

[Log in to Reply] [No Email]

Allan in NE

08-11-2004 05:51:38

Report to Moderator

Re: IH 666 oil leak in reply to AndyinMo, 08-11-2004 05:39:52

Hey Andy,

Have you tried loosening the clutch on the lever? Maybe that will help you ease 'er out of there.

After you get the thing repaired, I'd pull out that standpipe in the corner of the compartment to drop the level down a couple of inches.

Why IH wants that tank to be "full" all the time is beyond me; it's just dead space taking up oil and making it ride up against that upper gasket.

Just a thought,

Allan

[Log in to Reply] [No Email]

AndyinMo

08-11-2004 08:28:49

Report to Moderator

Re: IH 666 oil leak in reply to Allan in NE, 08-11-2004 05:51:38

Not sure what clutch I should loosen?? I am a shade tree mechanic at best. Thanks

[Log in to Reply] [No Email]

Allan in NE

08-11-2004 08:36:54

Report to Moderator

Re: IH 666 oil leak in reply to AndyinMo, 08-11-2004 08:28:49

Andy,

Clear out at the outer end of the lift lever shaft. The clutch is what keeps the lever in one position by tightening the 1/4" bolt/nut/clamp that is setting fore and aft.

Or, are you drivin out the roll pins from inside and takin' the whole shootin' match out, tube and all?

Allan

[Log in to Reply] [No Email]

Andyin Mo

08-11-2004 09:12:52

Report to Moderator

Re: IH 666 oil leak in reply to Allan in NE, 08-11-2004 08:36:54

Thanks a bunch. I will try one or both ideas. I am leaving work early to try and get this problem fixed Thanks again Andy

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy