Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Farmall & IHC Tractors Discussion Forum
:

super C serial #

Welcome Guest, Log in or Register
Author 
oldiron29

05-19-2008 15:59:44




Report to Moderator

Can't find the tag or plate on super C.
Where should it be?
Is there a machined flat on motor with #?
Where would it be witch side? thanks for any help oldiron29




[Log in to Reply]   [No Email]
Hugh MacKay

05-20-2008 17:46:35




Report to Moderator
 Re: super C serial # in reply to oldiron29, 05-19-2008 15:59:44  
oldiron29: here are some serial numbers that could help you zero in on the tractor serial number. In June of 1952 tractor serial number 149945 had engine serial number 151959, a difference of 2014. In July 1954 tractor serial number 195652 had engine serial number 204642 a difference of 8990. The tractor serial number started off at 100001 in 1951, I don"t have the beginning engine serial number but am assuming it was the same. I think it is safe to say the tractor serial number and engine serial number spread increased by slightly over 2000 each year. The Super A did the same after serial number 310300 in 1951, and that spread developed to roughly 2800 by 1954.

In both cases those extra engines went for use as stationary engine use. Prior to that time, stationary engines had a separate sequence of serial numbers. Balers used some, I can remember in the 50s just about every ferris wheel, merry go round, etc. in my area was powered by a C-113 or C-123 engine. One problem I have with these figures, if amusement rides across North America used as many of those engines as in my area, there must have been another series of serial numbers. Very likely it was old engines hanging on from A, B, early SA and C days. I remember the outfit that came to our fall fair with amusement rides, they had about 6-8 of those little engines, and the guy keeping them running was grease from head to toe, and I think the same grease was on him the day they left town as the day they arrived. He was a nice old guy, but I bet he hadn"t seen a decent bed or bath since spring. I talked with him once, said his company had enough equipment to keep 4 shows on the go at same time. He said they had used other engines, however none measured up to those little IH engines. They had two extra engines with them at our fair. The day I talked with him he was putting a piston and sleeve kit in an IH engine.

[Log in to Reply]  [No Email]
Wes Dexter

05-19-2008 19:24:39




Report to Moderator
 Re: super C serial # in reply to oldiron29, 05-19-2008 15:59:44  
I have a 1954 Super C and there is a metal tag on the seat box that has the tracor serial number on it. When you are walking up to the back of the tractor it is on the right side.



[Log in to Reply]  [No Email]
CNKS

05-19-2008 17:10:14




Report to Moderator
 Re: super C serial # in reply to oldiron29, 05-19-2008 15:59:44  
Engine serial and chassis serial do not match on the SC. Most of the castings have codes on them that tell the date when cast. In the form of 1*8*U--Jan 8 1951. The * looks like a screw head. U and W are 51, X,Y, and Z indicate 52,53,54. Casting dates can be a couple of weeks to 3 months or so earlier than actual assembly.



[Log in to Reply]  [No Email]
oldiron29

05-19-2008 17:26:22




Report to Moderator
 Re: super C serial # in reply to CNKS, 05-19-2008 17:10:14  
CNKS, I will go back and look I did not have good light in back of barn I will bring flash light when I go back. I no the casting codes so I will look for them there is no tag on tool box. Thanks oldiron29



[Log in to Reply]  [No Email]
ScottyHOMEy

05-19-2008 16:28:32




Report to Moderator
 Re: super C serial # in reply to oldiron29, 05-19-2008 15:59:44  
Chassis Ser # plate should be riveted to the right side of the toolbox that makes the base for your seat. Engine Ser # will be stamped into a machined flat spot at the top of the crankcase, right below your #1 plug. It might be obscured by the rod to the governor, but that's the spot.



[Log in to Reply]  [No Email]
oldiron29

05-19-2008 17:28:24




Report to Moderator
 Re: super C serial # in reply to ScottyHOMEy, 05-19-2008 16:28:32  
Scotty, there is no tag so I will look for casting code. Thanks oldiron29



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy