Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Farmall & IHC Tractors Discussion Forum
:

400 Engine Question

Welcome Guest, Log in or Register
Author 
Too Far Gone

04-22-2008 16:25:51




Report to Moderator

I have a 400 and the gear that runs against the crank,and the governor(The Idler Gear)has a bushing in it that is wore out and needs replaced.IH says its not available,havent found it aftermarket either.Any Suggestions or availability to the parts out there?Thank You




[Log in to Reply]   [No Email]
Janicholson

04-23-2008 05:45:42




Report to Moderator
 Re: 400 Engine Question in reply to Too Far Gone, 04-22-2008 16:25:51  
A good machine shop can put a new bushing in the hole for a reasonable cost. Between shipping and stocking costs, probably cheaper. They will need the shaft size, and the gear, JimN



[Log in to Reply]  [No Email]
Janicholson

04-23-2008 05:45:38




Report to Moderator
 Re: 400 Engine Question in reply to Too Far Gone, 04-22-2008 16:25:51  
A good machine shop can put a new bushing in the hole for a reasonable cost. Between shipping and stocking costs, probably cheaper. They will need the shaft size, and the gear, JimN



[Log in to Reply]  [No Email]
D Slater

04-22-2008 18:25:41




Report to Moderator
 Re: 400 Engine Question in reply to Too Far Gone, 04-22-2008 16:25:51  
At least one aftermarket supplier of engine parts used to furnish the bushings to engine rebuild shops, they had to be sized most times though. Haven't tried to get one for a few years so don't know if the information is current. Valu Built Tractor parts in Iwoa did sell used idler gears with a new bushing installed also. Think IH just starter selling the gear bushing and hub complete is probably the reason parts person can't find it.

[Log in to Reply]  [No Email]
Too Far Gone

04-22-2008 22:19:34




Report to Moderator
 Re: 400 Engine Question in reply to D Slater, 04-22-2008 18:25:41  
Slater,Appreciate the info.IH Looked up the gear with a bushing in it,and said Not Available



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy