Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Farmall & IHC Tractors Discussion Forum
:

MW

Welcome Guest, Log in or Register
Author 
Pat-CT

03-16-2008 19:24:47




Report to Moderator

does the M&W govner really work for the H just looking for a little more umph on hills and stuff like where i dont have to start off with a hay trailer without a lot of bogging and i wouldnt mind more power for the 1 pull i do during the year but ho much is a working one worth and do they really make a diffrence




[Log in to Reply]   [No Email]
Janicholson

03-17-2008 10:44:47




Report to Moderator
 Re: MW in reply to Pat-CT, 03-16-2008 19:24:47  
From a prior post of mine, JimN
The only way a governor can assist actual power is to be more responsive to load. Thus opening the throttle wider faster to keep engine RPM farther into the High Idle zone when the throttle control lever is at the stop. (of course if it allows higher RPM this would be different, and I assume original high Idle.
Example: ----If---- an IH governor opened 15 degrees of more throttle when 50 RPM was dropped, and was full open (from high Idle) at 100 RPM drop, and we compared that to a different governor (because I have no data on any governors) that was opening 25 degrees at 50 RPM drop, and full open at 70 RPM drop, The second governor would be more responsive in the effort to keep the RPM up above rated load RPM.
Ith primary difficulty is dampening the tendency to surge when the governor is super responsive. I believe the M&W is well dampened and not much would change in normal operation, the true PTO RPM might require slightly lower throttle control lever position to maintain RPM under light load. this would not actually change the effective throttle plate opening, but could make it seem like there was more power.
Old cruse controls on cars were like that, they let the rpm (speed) sag some befor compensating. New vehicles are so precise that the speed stays nearly perfectly at the setting until the mountain being climed pulls it down to the point that the throttle is wide open. Then the speed will continue to decline untill the engine reaches its peak load rating where it will be level for a while (unless the garde gets even steeper. I hope this helps, JimN

[Log in to Reply]  [No Email]
nebraska kirk

03-16-2008 21:04:56




Report to Moderator
 Re: MW in reply to Pat-CT, 03-16-2008 19:24:47  
I don"t think the M&W governer will give you more power. What it does is gives you faster throttle response under load.



[Log in to Reply]  [No Email]
Andrew Z

03-16-2008 20:48:20




Report to Moderator
 Re: MW in reply to Pat-CT, 03-16-2008 19:24:47  
Search the archives on that iv written alot on them over the past couple of years. id type it out again but have to run. let me know if you dont get there in hte archives, email open

Andrew



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy