TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Farmall & IHC Tractors Discussion Forum

Super C hydraulic block overhaul

Welcome Guest, Log in or Register

Author

riverbend

02-25-2008 16:02:09

Report to Moderator

I have several questions about rebuilding the hydraulic block on my Super C.

How do you get the check valves, bushings, and actuators out of the block ?

What does a 'drag link screwdriver' look like ?

In the Touch Control Serviceman's Handbook (GSS-1024) what are the circlip pliers used for ? It does not look like there are any C-clips.

There are several socket headed cap screws under the bottom cover. Should I take them out or leave them alone ? I don't see them listed on the exploded diagrams.

Many thanks

Greg

[Log in to Reply] [No Email]

AndrewFromNS

02-25-2008 17:33:45

Report to Moderator

Re: Super C hydraulic block overhaul in reply to riverbend, 02-25-2008 16:02:09

Did you have any trouble getting the Hydraulic Cylinder Head cover off yours? The one a friend and I are working on is being rather stubborn and uncooperative.

AR

[Log in to Reply] [No Email]

riverbend

02-26-2008 05:18:38

Report to Moderator

Re: Super C hydraulic block overhaul in reply to AndrewFromNS, 02-25-2008 17:33:45

No, I whacked it all over with a rubber hammer and tapped the edge of a thin putty knife about 1/8" into the gasket. After three or four places, it popped loose.

[Log in to Reply] [No Email]

Idaho Ron

02-25-2008 17:12:13

Report to Moderator

Re: Super C hydraulic block overhaul in reply to riverbend, 02-25-2008 16:02:09

Riverbend, What was going on with yous that you thought you needed to overhaul it? Ron

[Log in to Reply] [No Email]

riverbend

02-25-2008 17:24:54

Report to Moderator

Re: Super C hydraulic block overhaul in reply to Idaho Ron, 02-25-2008 17:12:13

I'm in the process of rebuilding the motor. Since it was all apart any way, I figured that I might as well go through the hydraulic pump and the block too.

Greg

[Log in to Reply] [No Email]

VAJerry

02-25-2008 16:25:07

Report to Moderator

Re: Super C hydraulic block overhaul in reply to riverbend, 02-25-2008 16:02:09

Blow compressed air into the different holes around the check valves etc, CAREFULLY. They will fly if you use too much pressure. A drag link screwdriver has a large bit and you strike it with a hammer to turn it. I did not need anything but common hand tools when I rebuilt the one on my Super A, which should be the same.

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy