Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Farmall & IHC Tractors Discussion Forum
:

'43 H clutch

Welcome Guest, Log in or Register
Author 
dan.160

11-06-2007 14:56:08




Report to Moderator

I need to press the clutch all the way down and only after the lever at the bottomm of the adjusting rod strikes the trans/motor housing does the clutch disengauge and allow shifting and stops the tractor. No slipping at all and strong! I"d just like the clutch to release earlier and not need to drop all the way to the bottom/striking the motor. How does one adjust this...what"s wrong with it. Thanks, Dan

[Log in to Reply]   [No Email]
dan.160

11-07-2007 20:47:15




Report to Moderator
 Re: '43 H clutch in reply to dan.160, 11-06-2007 14:56:08  
Thanks! Well, it doesn't disengauge untill its stretched/pushed all the way down. I had to remove the washer from the inside to that it would not hit the trans/housing and allow it to let go pressure so I could sit still or shift. You think this means splitting the tractor or is there an adjustment at the lower arm area?



[Log in to Reply]  [No Email]
Janicholson

11-06-2007 16:56:54




Report to Moderator
 Re: '43 H clutch in reply to dan.160, 11-06-2007 14:56:08  
Simple, or complex. It depends on thie following action.
Go to the tractor with a measuring tape, or ruler.
with your hand, push in on the clutch pedal until it changes its feel to be much harder to push. (from easy to hard) When it is at that spot, measure between the casting of the top of the trans (platform) and the spot on the pedal that touches the platform when the clutch is not being pushed. It should measure 1 to 1-1/4 inches. This is freeplay, and is necessary to keep the fingers off of the throwout bearing when the clutch is not pushed. Adjust the length of the rod connecting the pedal to the arm on the housing to make this measurement correct. If it is correct, the tractor will need to be split to repair the clutch Pressure plate (by replacing it) it may have cracks or warpage that prevents proper disengagement. Good luck, it is probable that the adjustment will do the trick. Heat the turnbuckle if it is frozen, they do get rusty. JimN

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy