Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Farmall & IHC Tractors Discussion Forum
:

Farmall A Exhuast Manifold torque spec

Welcome Guest, Log in or Register
Author 
Chad from Michi

02-09-2007 06:11:33




Report to Moderator

Just like it says my IT shop book doesn't give me a torque spec that I can find for the exhaust manifold for a Farmall A.
Does anyone know it?




[Log in to Reply]   [No Email]
CNKS

02-09-2007 14:14:40




Report to Moderator
 Re: Farmall A Exhuast Manifold torque spec in reply to Chad from Michigan, 02-09-2007 06:11:33  
20 lbs -- see the link.



[Log in to Reply]  [No Email]
glennster

02-09-2007 06:25:46




Report to Moderator
 Re: Farmall A Exhuast Manifold torque spec in reply to Chad from Michigan, 02-09-2007 06:11:33  
i dont know the torque spec, but i did put a manifold on my b. same 113 motor. it has a coarse thread stud that goes into the block, and fine thread on the manifold side. i got a little overzealous with the tightening and pulled one stud out of the block, had to heli coil it. id guess maybe 25-30 lbs. best bet is use a 3/8 drive short handled rachet, snug em up, warm up the engine and re-tighten em. dont kill em, just get em firm. the fine threads generate a lot of torque.

[Log in to Reply]  [No Email]
ddg

02-09-2007 09:38:15




Report to Moderator
 Re: Farmall A Exhuast Manifold torque spec in reply to glennster, 02-09-2007 06:25:46  
That's the way I do it, tighten stuff till it strips, then back off half a turn.



[Log in to Reply]  [No Email]
Chad from Michigan

02-09-2007 06:45:20




Report to Moderator
 Re: Farmall A Exhuast Manifold torque spec in reply to glennster, 02-09-2007 06:25:46  
Ok sounds good that is basicly what I was planning on doing.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy