Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Farmall & IHC Tractors Discussion Forum
:

H Head Stud - Needed

Welcome Guest, Log in or Register
Author 
TDK

12-29-2006 22:17:03




Report to Moderator

Anybody have an idea of where to get one ? CNH says no longer avaliable & have not found a bad block to rob one from. No luck at Fastenal or McMaster-Carr. Size is: 7/16 X 5 15/16, 14 t.p.i.(coarse) & 20 t.p.i.(fine)threads. Thanks for any help.




[Log in to Reply]   [No Email]
TDK

12-30-2006 19:49:27




Report to Moderator
 Re: H Head Stud - Needed in reply to TDK, 12-29-2006 22:17:03  
I think I've found one, thanks to this board. I do really appreciate the offers though and will keep each one in mind if needed later. Thanks to Tom,Bill,JDR and all very much.



[Log in to Reply]  [No Email]
Marty Johns

12-30-2006 19:13:31




Report to Moderator
 Re: H Head Stud - Needed in reply to TDK, 12-29-2006 22:17:03  
I agree with Hal, But go 1 step further, Have a solid brass 3/4 inch flat driver and when heat comes off the drvr goes on and is smacked a couple times with a 5 # sledge then immediatly put a wrench to her!



[Log in to Reply]  [No Email]
Tom Windsor

12-30-2006 07:44:01




Report to Moderator
 Re: H Head Stud - Needed in reply to TDK, 12-29-2006 22:17:03  
I salvaged out 2 blocks and have a hand full of stud bolts. Happy to send you what you need. let me know at Twindsor@aol.com

Tom Windsor



[Log in to Reply]  [No Email]
Bill Geer

12-30-2006 04:55:37




Report to Moderator
 Re: H Head Stud - Needed in reply to TDK, 12-29-2006 22:17:03  
If the stud off a M is the same. I can try to take one out of a block and put it in the mail. Bill



[Log in to Reply]  [No Email]
RustyFarmall

12-30-2006 07:18:53




Report to Moderator
 Re: H Head Stud - Needed in reply to Bill Geer, 12-30-2006 04:55:37  
The head stud from an M is a larger diameter, it won't work on an H.



[Log in to Reply]  [No Email]
JDR

12-30-2006 03:29:52




Report to Moderator
 Re: H Head Stud - Needed in reply to TDK, 12-29-2006 22:17:03  
I have a couple of cracked H blocks-Tried getting studs out and snapped a couple off. Tell me how to easily remove studs with out breaking them,and we can work out a deal. email should be open. JD



[Log in to Reply]  [No Email]
El Toro

12-30-2006 03:52:43




Report to Moderator
 Re: H Head Stud - Needed in reply to JDR, 12-30-2006 03:29:52  
If you have acetylene/oxygen cylinders and torch I would heat those studs. Hal



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy