Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Farmall & IHC Tractors Discussion Forum
:

M Clutch Part Help Needed

Welcome Guest, Log in or Register
Author 
terryjd98

09-22-2006 17:26:12




Report to Moderator

Had to put a new clutch in a M. Got it all apart, out the hole in the bottom, new one installed but hit a snag. That one odd shaped piece with 4 holes that bolts to the shaft holder or whatever its called and the trans spline holder. I Cannot get that one little piece to fit no matter how I turn it. Piece will fit in but Can't get them rubber washers that goes on the bolts and and inbetween the pieces to fit. Can't remember now how it was turned when I took it off. Have turned it, flipped it tried about every way. Would anybody have a picture of this all together? A picture would tell me which way this part goes on. I am going to start taking a pic of everything now before I take it apart memory's not what it use to be. Thanks for any help Terry

[Log in to Reply]   [No Email]
John M

09-22-2006 17:58:04




Report to Moderator
 Re: M Clutch Part Help Needed in reply to terryjd98, 09-22-2006 17:26:12  
its possible that things have wore to the point where ti will only go in one way and you have to find it.I think you dont have the shaft far enough up in there or youre using new washers.



[Log in to Reply]  [No Email]
terryjd98

09-23-2006 15:50:27




Report to Moderator
 Re: M Clutch Part Help Needed in reply to John M, 09-22-2006 17:58:04  
Not using new washers. The shaft that goes through the clutch does seem to need to go about an 1/8 inch further. No way to get the bolts through the coupler to the trans shaft.



[Log in to Reply]  [No Email]
kfox

09-22-2006 17:46:24




Report to Moderator
 Re: M Clutch Part Help Needed in reply to terryjd98, 09-22-2006 17:26:12  
Terry, If your talking about the coupling that goes between the clutch shaft & transmission, the convex side of the plate goes toward the cluth on my H. M is probably the same. I've never worked on a M before, but I've heard they are built alike. ken



[Log in to Reply]  [No Email]
terryjd98

09-23-2006 15:52:39




Report to Moderator
 Re: M Clutch Part Help Needed in reply to kfox, 09-22-2006 17:46:24  
Thanks that does seem the way that coupler has to go on. Can't get it to go on but that looks the right way.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy