Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Farmall & IHC Tractors Discussion Forum
:

1947 Farmall A

Welcome Guest, Log in or Register
Author 
Bill in VT

07-04-2006 04:20:20




Report to Moderator

Won't start. Everything seems fine, except I notice gas pouring out of the "drip hole filler", which never happened before. Is there an easy fix to this? How would I renew the filler? Are parts available? And does anyone think this is contributing to the "no start"??Thanks to all for your help in advance.




[Log in to Reply]   [No Email]
CNKS

07-04-2006 09:17:17




Report to Moderator
 Re: 1947 Farmall A in reply to Bill in VT, 07-04-2006 04:20:20  
Every one of that style carb will flood if choked too much, and every one will leak out of that hole. If you say it has not done it before, then your float needle/seat may have finally given up. Just buy a kit for your carb, and replace the parts. Be sure to soak everything in carb cleaner, not parts cleaner, preferably overnight, after disassembly.



[Log in to Reply]  [No Email]
brfarmall

07-04-2006 07:26:00




Report to Moderator
 Re: 1947 Farmall A in reply to Bill in VT, 07-04-2006 04:20:20  
sounds like you have a hole in your float or the needle and seat are stuck also if gas is running out the overflow there is gas in your oil bath breather this will put the level to high and wont let it get enough air



[Log in to Reply]  [No Email]
Nat 2

07-04-2006 05:24:56




Report to Moderator
 Re: 1947 Farmall A in reply to Bill in VT, 07-04-2006 04:20:20  
That's an overflow drain, really.

Not picking on you specifically here, but it just baffles me how so few people know even the most basic troubleshooting techniques for a simple 4-stroke gasoline engine... Air, fuel, and fire at the right time. Suck, squeeze, bang, blow... They're not that complicated, yet so many people just stand there and scratch their heads, or check useless stuff like oil, coolant, muffler bearings...

Air is generally a gimmee. It takes a lot for the air passage to get plugged, and odds are if the tractor ran fine yesterday, the airway ain't blocked.

Timing is also usually a gimmee, if you shut the tractor off because you were done using it. All bets are off if the tractor went "BANG!" and suddenly quit, though. You'd have mentioned that in your post, though, RIGHT? (There have been cases where people have failed to mention OBVIOUS physical damage, i.e. a rod sticking through the side of the crankcase...)

Fire is the next thing to check. Magneto or distributor? If you pull the coil wire off at the distributor cap, hold it 3/8" from the frame, and have someone crank the tractor over, does a hot blue spark jump the gap? If not, you have no fire.

Fuel is the last thing. Carbs get stuck sitting overnight, and like Hugh said, you may need a carb kit. Then again, the gas draining may be a result of you cranking and cranking and cranking and cranking with the choke pulled. That sucks lots of gas into the intake, and it will run out the overflow.

Anyway, if it doesn't fire within the first few cranks, cranking on it more ain't gonna make it start. GET OFF the tractor and start troubleshooting.

[Log in to Reply]  [No Email]
Dave BN

07-04-2006 05:19:42




Report to Moderator
 Re: 1947 Farmall A in reply to Bill in VT, 07-04-2006 04:20:20  
If it takes a while for the gas to start comming out of the carb it may be because your cranking longer than usual without the engine running. Are you getting spark to the plugs? Are the plugs wet when you take them out. Do yu have old gas or water in the gas? You can get every part you need from several sources, I try to get mine from my Case/IH dealer as I find the quality is better. Dave.



[Log in to Reply]  [No Email]
Hugh MacKay

07-04-2006 05:07:30




Report to Moderator
 Re: 1947 Farmall A in reply to Bill in VT, 07-04-2006 04:20:20  
Bill: What you probably need is a carb kit. It may be just the float needing adjustment, however if your taking the carb apart, you may as well get the kit as they are not a big dollar item. The float is allowing too much gas into carb. These kits come with very good instructions and are quite simple to work on. No fancy tools needed. Most auto parts stores have these, although I think you get a better quality kit from CaseIH.

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy