TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Farmall & IHC Tractors Discussion Forum

super a alternator bracket

Welcome Guest, Log in or Register

Author

Bobby in SC

06-01-2006 17:33:24

Report to Moderator

Is there a special bracket made for the alternator when changing from generator to alternator on the Super A, or do you rig it the best you can? I have searched for such a bracket and can't locate one. Any help appreciated.

[Log in to Reply] [No Email]

IH fan

12-31-2009 06:26:12

Report to Moderator

Re: Checkrow planting and cultivating in reply to LenNH, 12-30-2009 15:45:45

[quote="LA in WI"](quoted from post at 00:59:43 12/31/09) Picture this scene with wire-checked corn:

Just before sunset.

Clear skies.

Slight breeze.

Corn about 6-10" high.

Freshly cultivated.

You are looking from east end of field, with sun glistening off (or thru) the leaves.

You can see all kinds of geometric rows, at many angles.

Beautiful. Just beautiful.
It sure was... although Dad quit check-row planting by the late '40s, I still remember seeing it well into the '50s, at least in NE Iowa. I know Dad never used check-row after going to a mounted planter on the C, I think in 1950, but it had the roll of wire with the planter. When Mom left the farm (mid-'90s) there was a very nice pull type 2 row IH planter left in the barn with the wire and it didn't look like it had ever been un-rolled or the stakes pushed in the ground.

[Log in to Reply] [No Email]

Hugh MacKay

06-01-2006 18:12:24

Report to Moderator

Re: super a alternator bracket in reply to Bobby in SC, 06-01-2006 17:33:24

Bobby: There is no such kit, much to easy to fabricate.

It's quite easy to make if you use the generator mount, just weld 3/16 x 2-1/2 x 6 inch plate on top of the old gen mount. Weld on two tabs with holes for alternator mounting pin. Change the alternator pulley to one of the old V8 GM double pulley. By using the outer pulley, this allows you to position alternator back far enough to clear the front of engine casting, and still tuck alternator in close to block. My alternator sits within 1/2" of the engine block.

Another thing I always do is space those tabs for alternator mounting about 1/4" wider than alternator mount. By using washers you can get the belt true. If you want a photo send me an e mail, I think I can find you a decent close up. It may be 130 or SA but they are both the same.

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy