TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Farmall & IHC Tractors Discussion Forum

Closer to being finished

Welcome Guest, Log in or Register

Author

Levi K

04-03-2006 19:13:17

Report to Moderator

Last thing left is the fuel tank and steering post. After that it's getting the dash on and getting it wired up. I checked with the local IH dealer and they said they could get me a harness from the alt. to the ignition switch for $80, a lot better than $200 from wiringharnesses.com. Oh, by the way- that hydrualic resivoir is HEAVY.

[Log in to Reply] [No Email]

River Bottom Farmer

04-03-2006 19:35:05

Report to Moderator

Re: Closer to being finished in reply to Levi K, 04-03-2006 19:13:17

That what I call a real tractor.Looks like your doing quite a few repairs do you intend to paint it and are you going to post picture if you do....Lookin good River Bottom Farmer

[Log in to Reply] [No Email]

Levi K

04-04-2006 19:40:18

Report to Moderator

Re: Closer to being finished in reply to River Bottom Farmer, 04-03-2006 19:35:05

Yeah, your not kiddin' lots of repairs- TA, road gear, all the gaskets and quite a few little other things that my grandpa did to make it more "modern" This is a 4-H project so I am going back to close-to-original. And, of course, I will definatly put a picture when finished on.

[Log in to Reply] [No Email]

Peabody

04-03-2006 19:30:25

Report to Moderator

Re: Closer to being finished in reply to Levi K, 04-03-2006 19:13:17

Looking good! BTW, with a wiring diagram from Bob M, you can make your own authentic-looking wiring harness a heck-of-a-lot cheaper than you can buy one. There"s really not that much to them.

[Log in to Reply] [No Email]

Yugrotcart

04-04-2006 13:00:00

Report to Moderator

Re: Closer to being finished in reply to Peabody, 04-03-2006 19:30:25

I used Bob M's diagrams and made a harness for my W6. I used shrink tube as a modern alternative to wire loom, and also soldered on all the connectors. Works great and looks good too..... ..

[Log in to Reply] [No Email]

Levi K

04-03-2006 19:14:18

Report to Moderator

Re: Closer to being finished in reply to Levi K, 04-03-2006 19:13:17

That resivoir

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy