TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Farmall & IHC Tractors Discussion Forum

1066 Draft Lever

Welcome Guest, Log in or Register

Author

Wicksfield

03-30-2006 06:32:27

Report to Moderator

The Draft Lever on my 1066 does not work properly. When pulled back, it wants to spring back into the down position. There is no implement attached to the 3-point.

What do I need to do to fix it?

[Log in to Reply] [No Email]

the tractor vet

03-30-2006 07:03:34

Report to Moderator

Re: 1066 Draft Lever in reply to Wicksfield, 03-30-2006 06:32:27

Tighten the bolt in the control rod bearing support it is on the back side and is a 5/16th's bolt that goes thru , it may be rusted so becareful as it will break the best way is to remove it and clean the threads and add a dab of neverseeze then tighten it up just enough to add friction to hold the draft sencening lever in place but not enought that it will not move it is sorta of a feel setting .

[Log in to Reply] [No Email]

Wicksfield

03-30-2006 07:34:24

Report to Moderator

Re: 1066 Draft Lever in reply to the tractor vet, 03-30-2006 07:03:34

Thanks Tractor Vet. Where is this bolt located exactly? Do I have to take any covers off?

[Log in to Reply] [No Email]

Allan In NE

03-30-2006 10:08:24

Report to Moderator

Re: 1066 Draft Lever in reply to Wicksfield, 03-30-2006 07:34:24

Wick,

Follow the lever down to the base; you'll see the clamp. There is one for each lever.

If you use the 3-point a lot, this is usually a yearly chore to "give 'em a little snug".

Allan

[Log in to Reply] [No Email]

Wicksfield

03-30-2006 12:43:57

Report to Moderator

Re: 1066 Draft Lever in reply to Allan In NE, 03-30-2006 10:08:24

Thanks Allan. I don't use the 3 point on this tractor at all but it bugs me if things don't work right. I know, I'm weird.

[Log in to Reply] [No Email]

Allan In NE

03-30-2006 14:24:58

Report to Moderator

Re: 1066 Draft Lever in reply to Wicksfield, 03-30-2006 12:43:57

I'm the same darned way. If something doesn't work right, it just drives me bonkers 'til I get it fixed.

Allan

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy