TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Farmall & IHC Tractors Discussion Forum

Super C Grill Mounting Help

Welcome Guest, Log in or Register

Author

SuperCDon

01-31-2006 05:11:38

Report to Moderator

The front grill for my Super C was torn around the crank hole and front mounting bolt hole. I patched it, but now I need to know the hole size and location for the front mounting bolt. Could somebody make a simple paper pattern from their Super C to show the location and size and then e-mail or mail it to me? That would be very helpful. Also, the crank bracket (to which the lower grill bolt screws) seems to not be at the correct angle. What is the correct angle for the nut? See the attached photo.

[Log in to Reply] [No Email]

SuperCDon

01-31-2006 18:01:32

Report to Moderator

Re: Super C Grill Mounting Help in reply to SuperCDon, 01-31-2006 05:11:38

This is the upper grill mount bracket. I think it is bent backwards toward the tractor and should be square to the front of the tractor. Is that correct

[Log in to Reply] [No Email]

SuperCdon

01-31-2006 16:06:04

Report to Moderator

Re: Super C Grill Mounting Help in reply to SuperCDon, 01-31-2006 05:11:38

Thanks Brownie...the bolt is 5/16 fine thread with a 9/16" head..I'll work on getting everything lined up and drill the hole.

[Log in to Reply] [No Email]

gab

01-31-2006 12:08:53

Report to Moderator

Re: Super C Grill Mounting Help in reply to SuperCDon, 01-31-2006 05:11:38

I just measured mine, center of the hole 2 inches below seam and in center line of the grille. It's probably a 3/8th inch hole and bend the end of that brkt. back a little more toward the radiator. Jim

[Log in to Reply] [No Email]

SuperCDon

01-31-2006 16:04:15

Report to Moderator

Re: Super C Grill Mounting Help in reply to gab, 01-31-2006 12:08:53

Thanks GAb--this is just what I needed. I"m going out now to bend that brkt back a bit. Thanks for taking the time to answer my query.

[Log in to Reply] [No Email]

Brownie 45

01-31-2006 10:37:59

Report to Moderator

Re: Super C Grill Mounting Help in reply to SuperCDon, 01-31-2006 05:11:38

If I remember correctly, the"nut" on the end of your bracket needs to be nearly verticle [ 90 degrees ] so the grille bolt will match up correctly. I think that the hole in the grille is slightly oversize compared to the bolt. Guessing here, but the bolt is either 5/16" or 3/8" and the hole in the grille is maybe 7/16". Possibly 1/2". Someone may be more exact. When we had the grille off, we would re-mount it starting with the top 2 bolts & then eyeball the front lower bolt hole with a little judicious bending of the bracket in your photo.

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy