TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Farmall & IHC Tractors Discussion Forum

zenith carb which one?

Welcome Guest, Log in or Register

Author

banjo

12-30-2005 12:01:37

Report to Moderator

I have a 1948 super A that has a zenith carb, but no numbers to identify which model.

the carb is all cast , only zenith made in usa on it. has a 6 stamped in the bottom sectin and a 2 on the top half. that is the only numbers on the entire carb.

how can i find which repair kit it needs?

[Log in to Reply] [No Email]

banjo

12-30-2005 19:54:11

Report to Moderator

Re: zenith carb which one? in reply to banjo, 12-30-2005 12:01:37

i seen the kits on this site i just wasn't sure which one i needed. Not sure where dealers are 50 miles to big town, not sure there is a dealer there. probably be 80 miles. going to be an all day trip and then a repeat couse i dought they will have one in stock.

[Log in to Reply] [No Email]

banjo

12-30-2005 19:54:10

Report to Moderator

Re: zenith carb which one? in reply to banjo, 12-30-2005 12:01:37

[Log in to Reply] [No Email]

Mark in TN

12-30-2005 12:32:10

Report to Moderator

Re: zenith carb which one? in reply to banjo, 12-30-2005 12:01:37

Banjo, I had a similar problem when I went to rebuild my carb, except mine had 3-63 and B6 in the bottom of the casting. I found a place that sells these kits at www.carbsonly.com. The kit they sent was for 6 different Zenith models (61, 62, 67, 68, 161, and 267). The kit P/N was 778-615A made by BFIC. The cost was $21.95 + $4.85 shipping in '03. I think the only real difference in these carb rebuld kits is the gasket that goes between the two halves and the bowl vent. You can send them an email and they will help you get the right kit.

Carbsonly

[Log in to Reply] [No Email]

Andrew Z

12-30-2005 12:22:03

Report to Moderator

Re: zenith carb which one? in reply to banjo, 12-30-2005 12:01:37

The book list zenith 167x7 or 67x7, also zenith 161-7 is also listed. I thing that most of the Super A had the 167x7 carb not sure though. As to were to get a kit there all over the place, you can find them on this site, or at your local Case IH dealer. Take the carb down to the dealer and have them help you out. Andrew

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy