Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Farmall & IHC Tractors Discussion Forum
:

Help Again

Welcome Guest, Log in or Register
Author 
John Quillen

12-03-2005 12:35:03




Report to Moderator

I had to take the belt pulley shaft out and replace the oil seal on a Farmall H. When I took the 3 bolts out that hold the shaft in, I would guess that a pint of water ran out? Wow!! That much condensation? Anyway, my question is:(The repair manual I have doesn't say) What type and how much fluid goes back in? I'm guessing a heavy gear lube would be okay, but how much? Thanks again for your help...

[Log in to Reply]   [No Email]
Haas

12-03-2005 18:13:01




Report to Moderator
 Re: Help Again in reply to John Quillen , 12-03-2005 12:35:03  
Water always goes up to the belt pulley, as it is the highest and coolest point and that is where the water will condense. As CNKS said, same oil as in trsnsmission. Add a quart to the belt pulley when you put it back together. Water in the belt pulley housing will cause the bearings to corrode which is not good. To help the problem, run the pulley every so often and hopefully some of the water will go back to the transmission. Then if you work the tractor and get things hot the water will go away. Recently, I overhauled the transmission on a Super H. I found the transmission does not drain completely out of the rear compartment if the tractor is level. You first need to drain at both the front and rear drains with the tractor level and then elevate the front about a foot to get most of the oil (and/or water out) With the tractor level, the differential compartment probably had a quart of more left in there, of which half or more was water.

[Log in to Reply]  [No Email]
CNKS

12-03-2005 13:59:19




Report to Moderator
 Re: Help Again in reply to John Quillen , 12-03-2005 12:35:03  
The pulley is lubricated from the transmission. It's a good idea to add oil into the pulley mechanism after disassembly, at other times it is splash lubricated from the transmission. But, water in the pulley means the trans/diff is also contaminated, you need to change the fluid in the whole thing. 90 or 80W-90, etc. 6 gal, or until it runs out the check plug on the left side.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy