TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Farmall & IHC Tractors Discussion Forum

M push pull ignition switch

Welcome Guest, Log in or Register

Author

Bob Underwood

11-01-2005 02:49:19

Report to Moderator

Ignition switch has been removed from my 49M, I would like to know if there is a difference between switch for mag and distributor
Thanks Bob

[Log in to Reply] [No Email]

Haas

11-01-2005 06:24:21

Report to Moderator

Re: M push pull ignition switch in reply to Bob Underwood, 11-01-2005 02:49:19

The one for the magneto just grounds the magneto when you push it in so it only has one connection. When pulled out the switch is open so no current flows. The one for the battery ignition is a standard single pole switch with one contact and two connections. Switch contacts are open when pushed in, closed (ignition on) when pulled out.

[Log in to Reply] [No Email]

C Davis

11-01-2005 03:31:07

Report to Moderator

Re: M push pull ignition switch in reply to Bob Underwood, 11-01-2005 02:49:19

Yes the mag has one post and dist has two

[Log in to Reply] [No Email]

Bob Underwood

11-01-2005 04:36:53

Report to Moderator

Re: M push pull ignition switch in reply to C Davis, 11-01-2005 03:31:07

Thanks. E-Bay has one of the mag type thought I should chec. The tractor I have has a distributor. Thanks
Bob

[Log in to Reply] [No Email]

Peabody

11-01-2005 05:22:25

Report to Moderator

Re: M push pull ignition switch in reply to Bob Underwood, 11-01-2005 04:36:53

You can get a new one from OEM Tractor Parts for $51.00 (!?!?!?!?!).

[Log in to Reply] [No Email]

TKN

11-01-2005 09:22:27

Report to Moderator

Re: M push pull ignition switch in reply to Peabody, 11-01-2005 05:22:25

Can you use a two post type on a Mag system?

[Log in to Reply] [No Email]

Sorta

11-01-2005 09:33:05

Report to Moderator

Re: M push pull ignition switch in reply to TKN, 11-01-2005 09:22:27

Yes by running wire from 1 post to ground but then it will be out to stop and in to run.

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy